Equipment Guide设备导引

Mouse over a number to view more information. 鼠标点击图片的数字，您可以得到对应部分的详细信息。

Standard Equipment标准配置

• Carbide Tooth Trimmer硬质合金整平器
  • Cuts through the hardest subgrade, speeding production • Long wear用于整平基层，使摊铺速度更快，长效耐磨。
• Cast Auger Conveyor: 蛟龙上料机构144″ (3.7m); 24″ (61cm) hydraulic cylinder shift  3.7长蛟龙传输机构，液压滑动行程达61厘米。
  • Speeds up pours!加速摊铺！ • Fully enclosed 全封闭结构• Moves concrete faster and keeps the machine cleaner 上料速度更快，保持机身清洁• Holds enough concrete to complete a tight radius, without delays caused by repositioning the ready-mix truck小半径摊铺时，由于蛟龙上料机构内保有更多混凝土，可以避免卸料车不断调整卸料位置，让小半径摊铺更加顺利 • Constantly mixes concrete. The separation of the mix caused by belt conveyors is eliminated, resulting in a strong, smooth curb二次搅拌混凝土，避免离析，使得出模效果更好 • Eliminates frequent replacement of belt conveyor相比皮带上料机构，蛟龙上料机构需要调节的频率更少 • For transport, the auger is repositioned to within the width of the main machine运输时，蛟龙上料机构可以方便调节到运输宽度位置
• High Pressure Washer: 高压水枪2000 psi (138 bar)  2000psi压力
  With water pressure of 2000 psi and an 132-gallon (500 liters) tank, there is plenty of water and water pressure for clean-up at the end of the day.    采用2000psi压力的水枪及配套的500升水箱，使得机身清洁更加方便快捷。
• Hydraulic Adjustable Offset: 侧位摊铺位置调节24″ (61cm) lateral shift; 25″ (63.5cm) vertical shift including 16″ (40.6cm) hydraulic lift and 9″ (22.8cm) mechanical lift   侧位摊铺位置水平液压调节行程为61厘米，垂直调节行程为63.5厘米，其中40.6厘米为液压调节，22.8厘米为机械调节。
  Position the mold independently of the machine for set-up versatility important for reconstruction work or reaching past obstructions. Also, work around catch basins while staying on the line, speeding production.   摊铺侧位调节功能至关主要，在狭窄工作空间或者拥堵的市政工程中，使得摊铺功能也能顺利进行。
• Hydraulic Right Rear Straddle Leg:右后支腿水平滑移功能 22″ (56cm) of side shift  水平滑移行程为56厘米。

• Hydraulic Vibrators:液压振动棒 2
  Two hydraulic vibrators consolidate concrete for consistent pouring. 振捣混凝土密实
• Mold: Up to 32″ (81cm) wide  模具：81厘米宽
• On-Board Water System: 132 gals (500 liters) stainless steel tank   随机供水系统：500升不锈钢水箱
• Proportional Electronic Controls  比例电子控制
• Quick-Release Hopper  快速装卸料斗
• Single-Lane Pour Capability  单车道摊铺功能
  Concrete truck is directly in front of the machine, resulting in quick, safe pours in single traffic lanes, or tight spots in parking lots   混凝土罐车卸料时与机器成一条直线，避免占用临近车道。
• Tracks: 12″ (30cm) wide  履带：30厘米宽
• Vibrator Circuits: 6  液压振捣回路：6条
  The machine comes equipped with 6 vibrator circuits, allowing you to pour 8-foot (2.4m) golf cart paths, or 5' (1.5m) barrier wall, without adding vibrator circuits.  机器配置6条液压振捣回路，即使摊铺2.4米宽，1.5米高的构筑物，也完全可以胜任。

Optional Equipment 备选装备

• Quick Connect Mold Mount System快速模具更换系统
  This option allows molds to be changed hydraulically in only a few minutes without heavy hand work. This saves as much as 30 minutes or more per mold change.  通常手工更换模具不但费力，时间至少花费半小时以上，而按照快速模具更换系统，几分钟内就可以更换全套模具。
• Hydraulic Front-Grade Control液压前纵坡控制
  Our optional Hydraulic Front-Grade Sensor Control allows the sensor to stay on line in a radius as tight as 7' (2.1m) without a crew member's assistance. Two versions of the kit -• an operator controlled cylinder and a fully automatic cylinder -• are available.The Operator Controlled Front-Grade Sensor Option allows the operator to hydraulically guide the sensor in and out by using a switch. 极小半径摊铺时，无需额外增加人力，液压前纵坡控制功能传感线依然和基准线保持良好接触。共有两种选择，及人工控制油缸和全自动控制油缸。
• Sensor Controlled Front Grade Arm前纵坡传感器臂
  The Fully Automatic Front-Grade Sensor Option uses an additional sensor mounted at the grade sensor that directs the sensor in and out through a radius. This eliminates the need for the machine operator to keep his eye on the stringline while turning radii. 当采用全自动前纵坡控制时，需要选择前纵坡控制臂。
• Digital Network Control System数字网络控制系统
  Operator has more control when changing the curb and gutter cross-slope on the fly使得摊铺横坡控制变得更加容易 • More production! 生产率更高！• Slope Compensation (Patented)横坡补偿控制（专利） • Crew does not have to manually lower steering sensor jacks or raise stringline height in order to keep the curb from being off from 1 to 2 inches (25 to 50 mm) because of machine movement 机器行走时如果横坡发生变化，工作人员无需手动调节传感器及基准线的位置• Machine automatically makes the correction for elevation 自动校正高程• Maintains true top-of-curb and back-of-curb reference to the stringline without manual adjustments to the grade and steering sensor jacks during transition, or calculating this amount of change in elevation and alignment, which saves time.使得基准线和摊铺构筑物严格保持一致，自动计算高程、横坡极其变化。
• Mold Mist Kit模具喷雾器
  The Kit eliminates the need for the crew to manually add water to the curb or sidewalk.  自动为摊铺构筑物喷加水雾。
• Stringline Kit基准线组件
  Instajust Stringline Kit • 48″ (122cm) stakes, 200 qty. • Slotted end line rods, 200 qty. • Instajust clamps, 200 qty. • 1,000' (1525m) rolls of string, 5 qty. (Other Kits Available.)  美国专业基准线组件，122厘米线桩共200只，槽式夹线器200只，线夹200只，5条1525米长基准线。
• Urethane Tracks履带橡胶板
  • 12″ (30cm) urethane tracking • Cushions machine to prevent marring the surface when running over recently poured concrete, such as stadium risers   30厘米宽履带橡胶板，避免刚履带破坏已摊铺路面。
• Auxiliary Water Tank辅助水箱
  93 gals (352 liters).Located beneath the machine.  352升辅助水箱，安装在机身下方。
• Charge Hopper Water System 料斗供水系统
• Light Kit照明组件
  • Light fixture with two 100-watt bulbs, included in the kit, is mounted to the front post for lighting direction of the machine 2只100瓦灯泡，安装在机器前方 • A second fixture with two additional bulbs, also included, is mounted to the rear post to light the pour. 2只安装在机身后方 • Well-lit views of the work in progress for machine operator and chute man 专业照明系统
• Dual Side Pouring 双侧摊铺功能
• MAX Package 重载升级组件包
• Spare Parts Kit备品备件
• Trimmer Extension:整平器加长件 6 inch (15cm)  15厘米长
  
• Trimmer Extension:整平器加长件 12 inch (30.5cm)   30.5厘米长
  
• Trimmer Extension: 24 inch (61cm)  整平器加长件  61厘米长
  
• Hydraulic Lift (for Barrier Mold) 防撞墙模具专用液压提升机构
  • Makes slipforming highway barrier or parapet easier.使得防撞墙及护栏摊铺更加容易 • Quickly lift barrier/parapet molds off rebar at the end of a day’s pour每天工作结束时，使得模具快速脱离模具内的钢筋架构 • Machine clean-up easier清洁机身变得更加容易 • With 3' (91 cm) of lift already built into the machine, the Hydraulic Mold Lift gives the machine an extra 2' (61 cm) of lift for easier maneuverability 机器本身可以提升模具行程已达91厘米，加上此系统，可获得额外的61厘米行程的提升空间 • Walls up to 50″ (1.3m) tall  可以摊铺1.3米高的构筑物
• Post Hole Digger Attachment 钻孔组件
  Saves hand work节省人力 • Digs post holes for highway safety cable barrier installations 在线缆护栏下方的混凝土基础中定位钻孔• Mounted on left rear of machine安装在机器的左后侧 • Hydraulics supplied from the aguer conveyor circuit, using the conveyor controls on the machine console液压动力来自于蛟龙液压系统回路，操作时采用蛟龙控制器操作 • Auger for post-hole digger operates inside cylinder, moving dirt upward into a hinged chute and catching the material before it hits the ground钻孔操作在套筒内进行，钻孔排料在套筒上方，避免排料在地上 • Hinged chute allows the material to be dumped out of the way of the slipform application and eliminates the need for a crew member to move the dirt manually 专用排料系统，无需人工清洁路面• Excavated material does not fall back into the hole; thus, the pier hole is left clean for the slipform operation排料系统使得所有钻孔后的排料完全清除，不会留在孔内 • Stop rod available for the attachment for consistency of hole depth孔深控制功能 • Requires a Quick Connect Mold Mount on machine. 需要和快速模具更换系统配套使用• Augers available at either 12″ or 15″ diameters. Consult factory for other desired hole sizes.钻孔孔径需提前通知力霸工厂定做。
• Mold Knife for Driveway Block-Outs模具挡片
  A curb mold accessory used to reduce labor and wasted material at driveway entrances. When engaged, it prevents material from filling the curb portion of the mold. A knife can be included in a mold order. 属于模具的一种附件，当摊铺位置和一些其它构筑物相连而此小段位置无需摊铺时，可以选择此附件。
• Hydraulic Offset Lock 液压侧位固定锁